CASTLE EURO Installationshandbuch PDF herunterladen (Seite 42)

EURO Programming Manual

Page: 42 RINS1291-3

4.17 Site Options

A full range of site options is available to tailor the operation of the system.

4.17.1 Site Option Types

Option Default

Function

Set With Fault Yes

If ‘YES’: Allows setting with the following faults active: Device

fail, Mains fail, Battery faults, Fuse faults, SMS failure, relay

sirens 1&2, relay Strobe faults.

Set With

Tamper+

If ‘YES’: Allows setting with the following faults active: Case

tamper and System tampers.

Set With ATS

Fault

Yes

If ‘YES’: Allows setting with the following faults active: Telecom

line fail, Modem failed, STU/ATE line fault, STU/ATE one path fail,

Digi dial fail, STU/ATE comms fail.

Set With

Ward TFault*

Yes

If ‘YES’: Allows a ward to be set if mains, battery, telecom line,

or other system fault is present.

Set Fail =

Alarm

If ‘YES’ = A graduated alarm will be generated when ‘Set Fail’

timer expires (see Change Timers), if exit procedure is still

incomplete. Set fail output will trigger.

If ‘NO’ = Exit time will continue until the Exit route is clear.

Do Bat Load

Test

If ‘YES’: Programmes the system to perform a full load test of

the battery at 7.00am each day.

Ward

Misoperation*

If ‘YES’ Allows a Misoperation (Abort) signal to be generated

without the entry of a valid code into the system when a ward is

operated after an alarm.

Strobe

Confirm

If ‘YES’: A ‘STROBE ANY’ output will be activated for 5 seconds

as the system arms. Use with care, in view of potential security

risk.

Re-Arm Omits No

If ‘YES’: At rearm at the end of the confirmation time, this

function will force an input (not a system tamper) causing an

unconfirmed alarm to be omitted, whether it’s still in fault or not.

Use Level

Set*

If ‘YES’: The system becomes a ‘level set’ (Having one area set

only at any one time, e.g. part sets). If ‘NO’: The system

becomes a ‘area’ system (setting more than once area at a time)

Confirmed

When

Final

Set

Final Set: Confirmed signal only available after the system is

set. Exit Starts: Confirmed signal available after the exit time

has started. NOTE: Not compliant with DD243.

Note: ‘Exit Starts’ must be selected in order for it to be entered in

the logs.

AutoSet

Force*

If ‘YES’ when autoset is in use (this is only available in the plus

software) the panel will still set even if an input is open at the

time.

Restrict PIN

Use

If ‘YES’ the system prevents a pin code being entered on the

Entry Time, but allows the system to be silenced once in alarm.

Enable when DD243 option 6.4.5 is in use.

Simple Set No

Enables the ‘simple set’ functionality which allows a user to set

the system by pressing the ‘YES’ key and the level set.

PLEASE NOTE THIS FEATURE IS NOT UK COMPLIANT

Invert ATE

O/Ps

Yes If ‘YES’: ‘Positive Removed’ If ‘NO’: ‘Positive Applied’

Common

Lobby*

Yes

If set to ‘YES’, this will automatically select the ‘highest’ exit

mode for all partitions. (0 = Timed, 1 = Final Door, 2 =

Timed/Final Door, 3 = PTS). For example, if Area C is selected as

Final Door and the rest of the partitions are selected as Timed,

then because Final Door is ‘higher’ than Timed (Final door is 1

and Timed is 0), all partitions will be set to Final Door. If set to

‘NO’ the Exit Modes will be individually programmable to each

area.

1 2 ... 37 38 39 40 41 42 43 44 45 46 47 ... 67 68

Kommentare zu diesen Handbüchern

Keine Kommentare

CASTLE EURO Installationshandbuch Seite 42

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme CASTLE EURO