CASTLE Meridian Spezifikationen PDF herunterladen (Seite 23)

Started Manual Castle Care-Tech Ltd

5·00 Page 45

12. TEST AND DIAGNOSTIC FACILITIES

AUTOMATIC TESTS

BATTERY TEST

The system performs a check of

the battery operation every 10

seconds, by dipping the power

supply voltage momentarily, and

measuring the system voltage. If

the battery voltage measured is

below 12·0v, or the battery fuse

has failed, a ‘BATTERY FAULT’

warning will be generated.

BATTERY LOAD TEST

Euro-MERiDIAN systems may be

set up to perform an automatic

‘Battery Load Test’ at every

power supply at 7:00 am each

day. This will drop the power

supply voltage below battery

voltage, and (G3+ and above)

switch a dummy resistive load

onto the system whilst

monitoring the system

diagnostics.

This test will NOT take place if:

the End Station Siren and

Strobe outputs are live

the system is in engineer

mode

any battery fault exists

any mains fault exists

the ‘site option’ is not

selected

If the test has already started, it

will be aborted if any of these

conditions apply, other than

entry into Engineer menu.

If the test is aborted, it will NOT

be performed until the next day.

This is selected in ‘SITE OPTIONS.’

The test may also be performed

as required, under engineer

control.

OTHER TEST FACILTIES

ENGINEER SYSTEM SET

This permits the engineer code

to set and unset the system.

With display showing

Euro-MERiDIAN

Time 13:45

Enter Engineer code (default

1111)

SET/UNSET SYSTEM?

Press YES

Set Areas

[ABCD]

Select security pattern to be

set, noting that the ABCD keys

will illuminate to reflect the

selection.

Press YES

Setting [30]

The system will commence

setting, in

‘

Timed

’

mode. Exit

time will count down, and

system set.

Castle Care-Tech Ltd Euro-MERiDIAN Getting

Page 46 Software

ENGINEER FORCE SET

This permits the engineer code

to set and unset the system,

forcing it to set despite zones in

fault condition, and nominate

which zone must be triggered to

generate an alarm condition.

With display showing

Euro-MERiDIAN

Time 13:45

Enter Engineer code

SET/UNSET SYSTEM?

Press NO

FORCE ARM ON 1st

ZONE [01]

Nominate number of zone to

generate alarm once set, eg

Press

and YES

FORCE ARM ON 2nd

ZONE [01]

Nominate number of

additional zone to generate

alarm once set, eg Press

and YES

Set Areas

[ABCD]

etc.

The system will QUICK

SET.

Note: In both cases, the system will

give correct ATS response to the

setting, and any resulting alarm

(including sequential confirmation

the zones selected provide a valid

combination

). On unsetting, the

system will revert to normal mode.

Note: If the system has been set by

any other code, the Engineer code

will NOT unset it.

KEYPAD DISPLAY TEST

Each Keypad display may be

tested individually. Press B for 5

seconds. All LEDs will light, and

the LCD will scroll the display to

test every pixel, reverting to the

normal display after 10 seconds.

ENGINEER TEST FACILITIES

Walk Test

Permits the detectors on the system

to be tested, for the entire system or

for selected area(s).

The display scrolls through all

programmed zones. As test is

conducted, system chimes, and zone

tested is removed from scrolling

display, until the last zone has been

triggered, or the test aborted.

Note: Exit from Engineer menu to

‘set’ programming before walk

test.

Soak Control

Any zone (except 'FX' types) may be

placed on 'soak test' to prevent it

from generating an alarm. Should it

trigger whilst the area to which is

allocated is set, the system will log

and indicate activation (at unset).

An option is also available to force

the system into 'Engineer Reset'

mode in the event of an activation.

Batt Load Test

Power supply voltage is reduced,

placing system and simulated alarm

load on battery.

Outputs Tests

Sirens (and strobes) can be tested

direct from menu.

Other output types can be selected

(NOT by individual output) using the

output type numbers - see page 44

ALL outputs programmed to that

configuration (inc. slot

in DigiModem

and plug

on ATE) will be tested.

1 2 ... 18 19 20 21 22 23 24 25 26 27

Kommentare zu diesen Handbüchern

Keine Kommentare

CASTLE Meridian Spezifikationen Seite 23

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme CASTLE Meridian