CASTLE Meridian Spezifikationen PDF herunterladen (Seite 16)

Started Manual Castle Care-Tech Ltd

5·00 Page 31

ZONE ATTRIBUTES

Attribute Response modification

Chime

System loudspeaker(s) will

‘chime’ when detector triggered

whilst relevant area is unset.

Note: zone concerned will NOT

indicate on display.

Single

System chimes once when

detector triggered

System chimes until detector is

cleared.

Applicable to ‘Intruder’ ‘FX’ ‘EN’ and

‘Switcher’ zones.

Omittable

Enables input to be manually

omitted during the setting

procedure

Normally

Open

Enables the system to respond

correctly when detectors of

‘normally open’ configuration

are wired to the system.

Alternatively converts input

types which default to ‘normally

open’ (eg PTS) to operate with

normally closed devices.

Double

knock

The control will only generate an

alarm if this input is triggered

twice within a pre-set period, or

if the input remains open for

that period.

Dual Trip

The Control will only generate an

alarm if this input, and another

like-programmed input

with

adjacent number

, are in active

condition at the same time.

Either detector in fault

condition will prevent the

system from setting.

Both

detectors must be wired

using the same technology (iD

or EoL) from the same device.

Special

Logged

Forces a log entry when the

input is opened or closed, even

when an alarm does not result.

May be selected to apply when

system is set, when unset, or

always.

Attribute Response modification

This attribute MUST be selected

for switcher inputs required to

activate SMS text messages.

Paired

Input

For use in Grade 3 iD systems.

Select to ‘YES’ for each of the

two biscuits acting as the input.

(see page 12 & 13)

Fault

Input

For use in Grade 3 iD systems.

Select to ‘YES’ for the biscuit

acting as the ‘anti-mask’ (biscuit

2 in figure 3 page 12)

Paired

With

For both biscuits enter the input

number with which each is

paired (see page 13).

Confirm

Group

Input will not 'confirm' an alarm

triggered by another input from

the same group. Groups 01 to 99

available.

Default '00' denotes

NOT part of a group.

Inputs allocated to ‘Group 99’

will generate an alarm that

results in an intruder

(unconfirmed) signal to ARC.

They will NOT under ANY

circumstances generate a

confirmed signal, regardless of

which group the input that

triggered the ‘unconfirmed’

alarm is allocated to.

See full Engineering Manual for

further details.

Any input may be programmed with

any combination of these attributes,

except where shown.

NOTE: Control of inputs on SOAK TEST

is located in the 'Engineer

Tests' menu -

page 46.

Castle Care-Tech Ltd Euro-MERiDIAN Getting

Software Page 32

PROGRAMMING STEPS

With the display showing

CHANGE INPUTS?

Press YES

Input Number

[01]

Press YES

Input Type

Isolated [00]

EITHER use

to scroll to

required setting OR key in

input type number from

table above – eg 07

Typ

Final Exit [07]

Press YES

Input Areas

[ABCD]

Use keys

to select the

security patterns required,

eg press

Input Areas

[AB ]

Whilst programming this

step, the keypad Area

(A,B,C,D) keys will illuminate

when that pattern is

selected.

Press YES

Input

Attributes?

Press YES

Chime

No [0]

Use

to select No [0],

Single [1] or Follow [2]

Press YES

Omittable

No [0]

Continue to select input

attribute options as

required, until

Input Name?

Press YES

ame

nput 01

Enter text to identify

input, as described on

page 23.

Press YES

Input Number

[01]

EITHER key in next input

number to programme, or

NO to exit function

CHANGE INPUTS?

Press NO

Moves to next menu

item

NOTE:

After programming the input, it is

necessary to exit engineering for

this to take effect, before the input

can be walk tested, etc.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 26 27

Kommentare zu diesen Handbüchern

Keine Kommentare

CASTLE Meridian Spezifikationen Seite 16

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme CASTLE Meridian