CASTLE Meridian Spezifikationen PDF herunterladen (Seite 17)

Started Manual Castle Care-Tech Ltd

Page 33 Software

ASSIGNING KEYPADS and

TAG READERS

Ensure that all Keypads and Tag

Readers are correctly addressed

BEFORE enabling them in this

menu.

Each Keypad / Tag Reader can be

assigned to SET and/or UNSET

specified security patterns,

EXCEPT for a G3+ used in LEVEL

setting mode.

In the case of area setting

systems, it is necessary also to

select the Area(s) IN – i.e. the

area(s) in which the set point is

located, to determine which exit

route and mode applies when it

is used to set the system.

See separate instructions for

using Tag Readers as Ward

Controllers, and for setting up

Access Control Points.

TMZ MODULES:

These are addressed and

programmed as Tag Readers.

AREA SETTING SYSTEMS:

Note that the areas that the TMZ unit

is programmed to be “IN” controls

the areas for which the loudspeaker

output will generate tones – thus an

‘area sounder’ output is possible.

ASSIGN KEYPADS/

READERS?

Press YES

Address

[0]

Use number keys (or

D

) to

select address

Press YES

Type

Keypad [0]

Use

D

to select Keypad [0] or

Reader [1].

Press YES

Default Level?

Set Point Sets Areas?

Select the system level /

areas that will be set when

code/tag is used at this point.

Set Point Name?

Permits location identification to

be programmed for Set Point.

Press YES

Set Point Name

Reader 0

Enter text, as described on

page 25.

Press YES

Address

[0]

Key in address of next

Keypad to be programmed,

or NO to exit.

OR

Castle Care-Tech Ltd Euro-MERiDIAN Getting

Page 34 Software

CHANGING SYSTEM

DISPLAYS

The display information referred

to on page 25 may be tailored to

suit the installation:

With the display showing

SYSTEM DISPLAYS?

Press YES

Area A Text

Area A

Enter text, as described on

page 28 and press YES

Repeat for each text string

Display When Set?

No [0]

Selects whether system

status information (ie

which areas are set) is

displayed, and alarm

events, whilst system is

set.

Permitted only Grade 1&2

systems using a means of

unsetting that does not use

an entry route.

Use

D

to select as required

and press YES

Repeat for each option

SYSTEM DISPLAYS

Press NO to move to next

menu

CHANGING TIMERS

The various timers on the system

are:

Timer

Function

Range

Default

Entry

Time

Entry time for

each Level or

Area

0

–

255

secs

30

Exit

Time

Exit time for

each Level or

Area

5

–

255

secs

30

Siren

Time

Cut off time for

external

sounder

2

–

99

mins

15

0-99

mins

30 Con-

firm

Time

Sets time

period during

which a second

activation must

occur to qualify

as 'sequentially

confirmed'

alarm.

Note: DD243

specifies

between

30 and 60

minutes.

Siren

Delay

Delay after

intruder alarm

before siren live

0

–

20

mins

00

NOT valid within three minutes of final

set, or if entry time started.

Strobe

Time

Time Strobe

output stays

live after end of

Siren time

0

–

99

mins

00

‘

99’ represents endless

Re

-

Arm

Num

ber

Number of

times system

re

-

arms after

end of

Confirmation

time

0

–

9

3

Note: rearm number applies to each

Level or Area, and does not affect

emergency alarms.

’9’ represents always rearm

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 26 27

Kommentare zu diesen Handbüchern

Keine Kommentare