CASTLE Meridian Spezifikationen PDF herunterladen (Seite 21)

Started Manual Castle Care-Tech Ltd

5·00 Page 41

Type Default Active Restore

0022 Final Set ANY

When FIRST area is set At code entry to unset LAST

area

0036 Shunt Fault

For use with shunt input – see Technical Note

“

Use of

Wards and Shunts.

”

Output type 0035/0036 cannot be fired by ATE pins.

0037 Reset 1

(Viper Reset)

At code entry to set After 3 seconds

0038

At code entry to set When unset

Reset 2

(Viper

Set/Unset)

triggers whenever an additional area is set.

0039 PIR Latch 1 When set (and in Walk

Test)

On alarm, or when unset

NOTE: restores and re-applied at 'Reinstatement' after unconfirmed alarm.

0040 PIR Latch 2

This is the inverse polarity to PIR Latch 1

0052

Mains Fail

ES 4

After pre-set time without

mains power

On restore of mains

0055

Global Fault 1

ATE9

During any fault if the

system is set.

At code to unset AND if fault

clear

0056

Global Fault 2

ATE9

During any fault at any

time

At code to silence AND if fault

clear

0060 Reset Digi ATE 8 At power up Live for 5 seconds only.

0064 Test ATS ATE 10 When output switched in

engineer menu

When test completed

0066 ATE Not Used ATE 8

ATE 9

Constant +5v, does not switch or restore

This configuration MUST always be programmed to STU output 8 if a

plug-on DIGICOM is in use (not required for STU).

Principal types from the above list are also available on a 'per Area' basis - see full Engineering

Manual.

The following types are available for all systems (see also type 035 for G3+ and MSX panels).

1001 Follow

zone 1

When input 1 is

activated

When zone clears

1256 Follow

zone 256

When input 256 is

activated

When zone clears

ie add 1000 to the input number to select the output type required.

Castle Care-Tech Ltd Euro-MERiDIAN Getting

Page 42 Software

SEQUENTIALLY CONFIRMED OUTPUTS

The first detector to alarm will cause

‘

intruder

’

signal to be sent to the

ARC, as an

“

UNCONFIRMED

”

alarm. If a

second detector goes into alarm

prior to the end of

‘

confirm' time,

the

“

CONFIRMED

”

signal will be sent

to ARC for notification to the police.

A repeat trigger of the first detector

will be ignored.

Two inputs within the same "Confirm

Group" cannot provide confirmation

(see page 31).

If the

‘

CONFIRMED

’

signal has NOT

been sent by the end of confirm

time, the system will reset and

(subject to setting of ‘rearm count’)

rearm. The ‘intruder’ signal WILL

restore. In the event of a further

trigger before the system is unset,

the full cycle of alarm events is

available, as above.

For additional information,

including operation on entry

route and other special

features, see full

‘

Engineering

Manual.

’

AREA SOUNDER OUTPUTS

There are no programmable

‘

area

sounder

’

configurations available.

However, the third output on a TMZ

module is configured as a

loudspeaker driver, and suitable

programming of the options for the

TMZ provides area sounder outputs

(see page 33).

PROGRAMMING STEPS:

With the display showing

CHANGE OUTPUTS?

Press YES

End Station

Outputs?

Press NO to move to next set

of outputs, or Press YES

Output 1 [014]

Siren Any

Use number keys to select

output type from table on

page 44, or

to scroll

through available options

Press YES

Output 2 [016]

Strobe Any

Repeat for Outputs 2, 3 and 4

Press YES

ATE OP 1

Fire [001]

Repeat for ATE OP 1 to 9

Press YES

End Station

Outputs?

Etc. to

CHANGE OUTPUTS?

Press NO

Moves to next menu item

NOTE: In some cases there will be

a delay of up to 10 seconds before

the display updates after selecting

an output type that ‘jumps’ an

unused type number.

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 27

Kommentare zu diesen Handbüchern

Keine Kommentare

CASTLE Meridian Spezifikationen Seite 21

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme CASTLE Meridian