CASTLE Meridian Spezifikationen PDF herunterladen (Seite 22)

Started Manual Castle Care-Tech Ltd

5·00 Page 43

INTELLIGENT SETTING

LEVEL SETTING SYSTEMS

Setting the system in pattern

‘

’

will commence

‘

intelligent setting

’

of the whole system, with the exit

tone at

‘

intelligent

’

volume level.

Activating the nominated zone

during exit time will cause the

system to switch to & set pattern

‘

’

AREA SETTING SYSTEMS

Setting the system with any code

including area B will initiate setting

the areas for which the code/tag is

valid, with the exit tone at

‘

intelligent

’

level.

Activating the nominated zone

during exit time will cause the

system to OMIT area B, and

‘

quick

set

’

the remaining areas.

In order to unset successfully, it is

essential that a detector be sited to

start entry time before entering the

code. If this is not done, additional

areas will set, instead of unsetting.

ALL SYSTEMS

If an FX zone is triggered before the

nominated zone, the system will

switch to full setting (or as

determined by code validity) and

continue to set, using normal exit

mode.

NOTES:

It is NOT possible to ‘Intelligent set’

other combinations of security

patterns.

If 'intelligent set' is in use, the exit

route must be designed so that an

‘FX’ detector can only be triggered

when the system is definitely

required to ‘fully’ set.

The 'intelligent' detector must be

sited to ensure that ALL potential

system users are correctly detected.

Some 'pet-immune' detectors are not

suitable.

Do NOT use a door contact as the

‘intelligent’ zone.

Programming Steps

With the display showing

INTELLIGENT SET?

Press YES

Intelligent

No [0]

Use

to choose No [0] or Yes

[1]

Press YES

Intelligent [--]

Insert input number required

to switch to

‘

Part

’

set and

press ‘Yes’. To remove an

input from the list, key in the

zone number again,

Press YES

INTELLIGENT SET?

Press NO

Moves to next menu item

Castle Care-Tech Ltd Euro-MERiDIAN Getting

Page 44 Software

SITE OPTIONS

A range of options is available to

tailor the operation of the system.

See full Engineering Manual for

details. Please note especially:

Rearm

Isolates

Forces the zone triggering an

'unconfirmed' alarm to be

isolated at rearm (re-

instatement) at the end of

'confirm' time, whether the

zone be in fault or not.

Use

Level set

Permits

Euro

44+ to be

selected to function in

‘

Level

setting

’

mode.

See

page 34.

ATE

Permits selection of inputs on

‘

plug

’

or loom connector

to suit

‘

STU

’

(inc. Red Care

Reset),

‘

Digicom

’

(inc. Fail to

Communicate),

‘

Relay

Interface monitoring

’

‘

not

used.

’

NOTE

: This option MUST be set to

'STU' or 'Digi' in order for Line

Fault (and other) Monitoring to

function.

Invert

ATE O/Ps

Changes outputs at ATE pins

(on End station only), to

trigger as “POSITIVE APPLIED”

instead of the default

“Positive Removed.”

Common

Lobby

If selected as ‘YES’ (default),

system will automatically

select the highest priority

exit mode from all the areas

that are capable of being set

from that set point.

If selected as ‘NO’, system will

select the highest priority

exit mode from these areas

actually being set at the time.

Restrict

Codes

If set to ‘YES’ then PIN codes

can still be programmed but

will not work during entry

time.

ENGINEER RESTORES

Engineer Resets may be performed by:

Use of Engineer code on site

Use of

‘

remote restore anticode

’

(if

option enabled) to generate a

reset code from a PC

programme that will perform

the Reset

Red Care Reset from Alarm

Receiving Centre

Download Reset from PC running

‘

Euro

InSite

’

software

If Engineer Restores are programmed, an

engineer must reset the system before it

can be used again. This will not interfere

with the generation of an emergency

alarm.

Options are available as follows:

Engineer Restore of HU

Following a Hold Up (HU Device or

Duress) alarm.

Engineer Restore of Intruder

Following an intruder alarm. This may

be selected to operate either on

generation of standard

‘

Intruder

’

signal, or

‘

Secure Intruder

’

signal.

Engineer Restore of Tamper

Following a Tamper alarm.

Engineer Restore of Soak

In the event of a zone with the

‘

soak

’

attribute triggering whilst the system

is set.

Engineer Restore of Confirm

Following an sequentially confirmed

alarm.

Anticode restore

Enables system to display an anticode

whilst awaiting Engineer Reset, which

can be used to generate a special

reset code.

1 2 ... 17 18 19 20 21 22 23 24 25 26 27

Kommentare zu diesen Handbüchern

Keine Kommentare

CASTLE Meridian Spezifikationen Seite 22

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme CASTLE Meridian